- Product Details
Quality Assurance Of Tmart Faucets:
Fit Your Water Pipe
The nut joint size of hosepipe can be divided into four types: 1/2",3/8",9/16",3/4".
German market is the 3 / 8 ", and the size of 1 / 2" is very generic in other countries
How to Install the Faucets:
Step1: Position the Faucet
A: Please place the gasket and faucet in position on the sink before installation B: Please thread the plastic mounting nuts onto the faucet shanks under the sink and make sure the large side of each plastic mounting nut is up C: Please check the faucet and gasket positions again from the top of the sink D: Please make sure to tighten the mounting nuts, but not to over-tighten. Over-tightening could damage the nuts and not easy to remove in the future. Step 2: Attach the Water Supply Tubes A: Use the Teflon tape to wrap the threads of the water-supply valve. Except for this Teflon tape, the plumber′s putty is recommended by some plumbing supply manufacturers. B: Please thread the water supply nut onto the shut-off valve and tighten the nut with a wrench. C: Use the Teflon tape to wrap the threads on the faucet shank, and then thread the water supply nut onto the faucet shank. D:Tighten the nut with a wrench.
Step 3: Connect the Faucet Lift Rod
A: Please insert the lift-rod into the faucet from the top of the sink until the pivot-rod is in the down position under the sink. Insert the lift-rod into the lift-rod strap, and tighten the screw.
B-1: Please ensure that the lift-rod opens and closes the drain plug as needed from the top of the sink.
B-2: You just loose the lift-rod strap screw and reposition the lift-rod if make any needed adjustments.
B-3: You just slide one end of the spring clip onto the pivot-rod if you need to connect the lift-rod strap to the pivot rod
B-4: Please ensure that both the pivot -rod and the lift-rod are in the down position. And insert the pivot-rod in the closest hole in the lift-rod strap.
Slide the other end of the pivot-rod. Make sure the lift-rod opens and closes the drain plug as desired.
B-5: Then slide the other end of the pivot-rod to ensure the lift-rod opens and closes the drain plug as needed.
C-1: You just need to loosen the lift-rod strap screw and reposition the lift-rod if you want to make minor adjustments for it.
C-2: You just need to remove the spring clip and move the pivot-rod to a different hole in the lift-rod strap if you want to make major adjustments for it.
How to maintain it
1.Please wipe the surface of water faucet with dry soft cloth gently (not with impurities). Do not use steel wire scrubber or buckram. In addition, the faucet of the surface should prevent collisions with hard objects in order to avoid damage to the water nozzle.
2.Do not use any type of cleanser with strong friction, cloth or paper cloth. Do not use any acid and alkali cleaner, polished abradant or rough cleaner.
3.Please use soft cloth (not with impurities) dampened with mild detergent solution to gently wipe the surface of water nozzle. Do not use steel wire scrubber or scouring pad. In addition, it should prevent collisions with hard objects in order to avoid damage to the water nozzle.
4.Please use the following cleansers to remove thick mask and surface deposit: mild liquid glass cleaner, pure liquid glass cleaner, non-acid and non-wear gentle liquid or completely dissolved powder, non-friction solution polish.
5.In the case of the water pressure not less than 0.02mpa (0.2KGF/cm2), after using period of time, if you find that the amount of water decreases or even the water heater switches off automatically, all you do is to screw out the cover screen at the faucet water outlet and remove impurities, generally can be repaired.
6.For the protection of the surface of electroplated coating, do not use chemical substances to clean the product surface, such as the cleaning agent containing alkali salt is known to have a very strong corroding effect on the surface, then wipe with a soft cloth dampened with clean water, and the clean water must be no hard objects such as dust or sand.
1.Don′t use a wet towel to clean the surface of water faucet directly
2.Don′t clean the water faucet with burr items
3.Don′t let the water faucet touch the acid-base solution
4.Don′t put the water faucet directly on hard surface
Please use dry and soft cotton cloth to clean the water faucet.
- Single handle design.
- Multi-layer finishing process, attractive looks.
- Ceramic cartridge is drip-free.
- Engineered for a lifetime of use.
- Good for home and commercial use.
- Unique, new, fashionable and modern design.
- This elegant faucet can be operated smoothly and precisely.
- Easy to clean and care for,easy to install.
- Be convenient to turn on.Die casting technology.
- Composition(Cu>59%,Pb<1.8%,Fe<0.3%),high Cu,low Pb.
- MS ceramic cartridge(600,000 times for both open and close).
- High quality material and finishing tested at a high water pressure of 1.6Mpa.
- Featured with durable ceramic valves ensuring there are no water leaks.
- The LED faucet will change its color by detecting water temperature. A. When water temperature is<30 degree,Blue color will show automatically;
B. When water temperature is between 30~40 degree,Green color will show automatically;
C. When water temperature is between 41-50 degree,Red color will show automatically;
D. When water temperature is above 51-100 degree,Red color will flash frequently.
Material Brass and glass Style Contemporary Valve Core Material Ceramic Working Temperature 0-100 degree Water Pressure 1.5 bar Feature LED, Waterfall Color Silver All Height 27.5cm / 10.83" Spout Height 21cm / 8.27" Spout Reach 7 cm / 2.75" Hose length 51cm / 20.08" Hose Specification G1/2′′, G3/8 Package Box Size 37 x 19 x 14cm Weight 1790g / 63.14oz
- 1 x Faucet
- 2 x Hose
- 2 x Threaded rods each with two nuts
- 1 x Semi - circular rubber gasket
- 1 x Semi - circular shim
- 1 x Battery compartment lid
- 1 x Parts
- 1 x manual